• 1900.636.256
  • ptssmarthome.com@gmail.com
  • 08:00am - 6:00pm

Schneider KNX High Bay presence detector FM

Schneider KNX High Bay presence detector FM


Hãng SX: Schneider

Mã Sản phẩm: MTN6304-0019

Máy dò phát hiện sự hiện diện KNX để lắp đặt trong các phòng có trần nhà cao, ví dụ: nhà kho hoặc nhà thi đấu thể thao. Máy dò sự hiện diện phát hiện sự hiện diện của người ngay cả trong trường hợp chuyển động nhỏ.

Mô tả

Hãng SX: Schneider

Mã Sản phẩm: MTN6304-0019


KNX presence detector for flush-mounted installation in rooms with high ceilings, e.g. high-bay warehouses or sports halls.
The presence detector detects the presence of persons even in the case of small movements.
Control of the lighting is carried out dependent on movement (2 channels) or additionally dependent on brightness (1 channel) via KNX telegrams. If there is sufficient daylight, the lighting is switched off or adapted to a detection brightness (constant light regulation).

Devices for heating, ventilation or air conditioning (HVAC) can also be controlled (1 channel).
The presence detector has two detection sensors (passive infrared), a brightness sensor, an IR receiver and an LED to indicate a detected movement, in test mode indication of the activated programming mode.
The presence detector can be used as a single detector or in master-slave mode. The setting is carried out in the ETS.
The presence detector can also be set and tested without the ETS, but with the appropriate remote control (available as an accessory). Indoor installation on ceiling (IP 20) on flush-mounted housing with two screws.
Optionally, a protective metal basket (available as an accessory) can be installed to protect the lens.

KNX software functions: Movement detection: The detected presence of a person is signalled using a KNX telegram. Lighting control: The room lighting is controlled depending on movement and brightness. If there is sufficient daylight, the lighting is switched off or dimmed to a constant level. Basic lighting: Activates basic lighting after the overtravel time has elapsed, either for a limited time or dependent on the brightness. HVAC control: Devices for heating, ventilation, air conditioning (HVAC) are switched from energy-saving mode to comfort mode dependent on movement. Operating modes: Single detector, Master, Slave, Master in parallel operation. Master: Controls the lighting and HVAC system. Additional detectors as slaves increase the area of detection. Slave: Only detects movement in its area and sends the information to the master. Master in parallel operation: Controls the lighting in its area (can be expanded with additional detectors as slaves). The only master in the installation only controls the HVAC system for the entire area. 2 logic gates.

Angle of detection: 360°
Opening angle: 180°
Range: Radius of max. 18 m (tangential)
Mounting height: 4 – 14 m
Optimal mounting height: 12 m
Time setting: 60 s – 255 min.
Sensors: 2 x passive infrared
Number of zones: 1416
Detection brightness: internal light sensor adjustable from approx. 2 to 1000 Lux
IP protection rating: IP 20
EC guidelines: Low voltage directive 2006/95/EC and EMC directive 2004/108/EC
Dimensions: 124 x 78 mm (Ø x H)
Accessories: Remote control for KNX presence detector MTN6300-0002
Protective basket for KNX presence detector MTN6300-0001

Thông tin bổ sung

Trọng lượng 0,278 kg
Công dụng

Chuẩn Kết nối


Nhà sản xuất


Đánh giá

Chưa có đánh giá nào.

Hãy là người đầu tiên nhận xét “Schneider KNX High Bay presence detector FM”

Email của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *

Tải File

Có thể bạn thích…